There is not a required ball mount for this Draw-Tite Trailer Hitch Receiver, part # 75673. Since you are worried about clearance I would recommend you use a Trailer Hitch Ball Mount, part # D-4. This ball mount has a distance of 10-1/4 inches from the center of the hitch pin hole to the ball hole. You would have plenty of clearance to run this ball mount in the rise position.
I attached installation instructions below as well as a review video of this hitch for you to check out. view full answer...
A Class l trailer hitch ball mount typically uses a hitch ball with a 3/4 inch shank.
If that is the case for your ball mount then I recommend a hitch ball like part # C40018. view full answer...
If your Explorer has a Class lll trailer hitch already installed I recommend the etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag.
If the ball mount kit does not include a ball mount with the right rise or drop to tow the trailer level, check out the link I have included that explains how to measure... view full answer...
Since the trailer you purchased has a coupler that requires a 2" hitch ball, you will need to either replace the 2-5/16" hitch ball on your current ball mount or purchase a separate ball mount with a 2" hitch ball when you need to tow that specific trailer.
If you are wanting to replace the hitch ball on your current ball mount you will need to measure the diameter of the hitch ball hole. Since it currently has a 2-5/16" hitch ball it more than likely has a 1-1/4" hole. For a 2" hitch... view full answer...
When you are towing a trailer you want the trailer to be as level as possible behind your F-150. I have attached a helpful article that explains how you can measure to find the best ball mount.
You just need a tape measure to do this. Park the truck on level ground and then measure form the ground to the top of the receiver opening. Then measure the distance from the bottom of the trailer coupler to the ground. If the hitch height is greater you will need a ball mount with a drop. If... view full answer...
In order to pull a trailer with your 2004 Chrysler Pacifica, you will need a trailer hitch, a ball mount, ball, pin and clip, and trailer wiring. For a trailer hitch, you can use the Draw-Tite hitch, # 75522, that you have referenced. I have included a link to the installation instructions and a link to a video showing a typical installation for you.
For a ball mount, ball, and pin and clip, I recommend the etrailer ball mount kit, # 989900. This kit comes with 2 ball mounts, a 2 inch... view full answer...
In order to choose the correct ball mount for your tow vehicle and trailer, you will first need to take a couple of measurements.
With your tow vehicle parked on level ground, take a measurement from the ground to the top of the trailer hitch receiver. Then with your trailer on level ground, measure from the ground to the bottom of the coupler. If the hitch height on your vehicle is greater, you will want to find a ball mount with a drop. If the coupler height is greater, you will want... view full answer...
In order to use the hitch ball part # 63912 in the ball mount part # D-4 you will need to use a hitch ball bushing part # C21100 since the shank of the hitch ball is 3/4 inch in diameter and the hole of the ball mount is 1 inch.
The ball mount will fit the hitch part # 13333 as-is though. For a hitch pin you would want part # PC3 or for a locking hitch pin # e98880. view full answer...
It sounds like you want a trailer hitch with a ball mount and hitch ball that can be removed. There are trailer hitches available for your 2011 Cadillac CTS Sedan that will allow you to use a 2 inch ball on a removable ball mount. The trailer hitch that I would recommend for you is the Draw-Tite Class I Trailer Hitch, # 24767. You would only need to add the ball mount and hitch ball. For a 2 inch hitch ball, use part # 19258. If you want a 1-7/8 inch hitch ball, use part # 19256.
Keep... view full answer...
For the Curt Class III Trailer Hitch # C13093 on your 2013 Chrysler 300, you will not need to use any specific ball mount. The ball mount you will want to use is the one that provides the correct rise or drop needed for you to tow your trailer level.
I have attached a help article on how to determine the needed rise or drop for your trailer.
A great ball mount kit option is the Ball Mount Kit for 2 Inch Hitches # 989900. This ball mount kit will provide you with a ball mount that offers... view full answer...
To tow a trailer with your 2011 Jeep Grand Cherokee you will also need a ball mount, hitch pin and clip, hitch ball, and wiring harness. Based on my research, the Draw-Tite Trailer Hitch on your Grand Cherokee is a 2 inch Class III trailer hitch, # 75699.
To provide you with a great starter kit for towing, I recommend the etrailer.com Ball Mount Kit for 2 Inch Hitches # 989900. This kit includes 2 ball mounts (one with a 3/4 inch rise or 2 inch drop and the other with a 2-3/4 inch rise... view full answer...
With your measurements you will need a ball mount with 1-1/4 inch of rise, though you can be within a half-inch of that and we do have some good options. You said 2-5/16 inch receiver, so I assume you mean that's the hitch ball size your coupler takes, but I'm not sure if your have a 2 inch or 2-1/2 inch receiver on your 2004 Chevy Silverado so I'll list options for ball mounts for both.
- 2 Inch Receiver: Convert-A-Ball Ball Mount # AMSC2HD
To mount to your hitch receiver it also requires... view full answer...
Sounds like you are looking for a 2 inch hitch ball and ball mount to fit into 2 inch trailer hitch. We have the Curt ball mount part # C45036 which is a ball mount designed for a 2 inch hitch and has a 2 inch hitch ball installed on it.
This ball mount has a 2 inch drop. For more info on how to pick out the correct drop/rise ball mount to tow your trailer level check out the help article I attached on the subject. view full answer...
The Curt hitch part # C11391 that you referenced is the correct hitch for your 2007 Honda Civic Ex coupe. For a ball mount you would want the part # C45521 and then for a 2 inch ball you would need the part # A-82.
For trailer wiring you would then want the # 118437. view full answer...
All of the aftermarket hitches we offer for your 2014 Ford F-150 also have the same 2-inch size receiver tube and this is the size that is compatible with the cushioned ball mount you referenced, Convert-A-Ball # AMSC4.
When choosing a ball mount you need to match the size, of course, but also the Class Rating (Class IV or Class V for the hitches we offer). You also want to choose a ball mount that has the correct amount of rise or drop to allow your trailer's frame to remain level with... view full answer...
For your 2005 Dodge Dakota Quad Cab V8, I recommend the Draw-Tite Aluminum Ball Mount # 4283 based on the coupler height you gave. It is a Class III ball mount with a 7 inch rise with a tow rating of 12,000 lbs. This mount will be a good fit based on your coupler height with the hitch height of the Hidden Hitch and Draw-Tite trailer hitches you referenced as it will provide a level tow for your boat trailer.
If you would prefer a more economic option, I would recommend the Draw-Tite 6-3/4... view full answer...
In order to pick out the correct ball mount you are going to know a couple measurements. You will first need to measure the hitch height from the ground to the top of the receiver opening. Next, you will need to measure from the ground to the bottom of the trailer coupler when the trailer is level and on level ground.
When you compare these numbers you will know the correct height ball mount to get. If the hitch height is higher than the trailer height you will need a drop ball mount.... view full answer...
By hitch I assume you are referring to a ball mount/drawbar as your 2011 Chevy Suburban should have a factory trailer hitch receiver already on it.
To tow a trailer or RV with a hitch weight (also known as tongue weight) of 1,300 lbs and a gross weight (or GVWR) of 11,460 lbs you are going to need a ball mount with at least those capacities.
Assuming that your '11 Suburban has a 2" trailer hitch receiver and your RV has a coupler that accepts a 2-5/16" hitch ball the best ball mount... view full answer...
We do not currently have any hitch adapters available that will expand the 2 inch receiver on your truck to a 2-1/2 inch receiver for use with your existing ball mount.
Your best option might be to simply replace your ball mount with one that is compatible with 2 inch trailer hitch receivers. I have attached a link that will take you to our available selection of ball mounts, as well as an article that explains how to choose the best one for towing your trailer level. I recommend looking... view full answer...
The Draw-Tite trailer hitch # 36336 and wiring harness # C55358 are correct for your 1999 Toyota Camry. The ball mount # 36061 is correct for the hitch as well.
There is a way to determine the right ball mount height to tow a trailer level but it is moot because you can't use a different ball mount other than what the hitch manufacturer specifies. But nevertheless I have included a link to the right that explains how to measure to choose the right ball mount should you need it for any... view full answer...
Go To Results